JKCrypto

How to Mine : Jolt Gas and many more coins mining guide

by 306 Comments

In this article I will be posting mining guides for all profitable coins to mine which are popping out everyday. All the Fast Miner download links are given in the table with optimal overclock settings.

Earlier I used to create  separate articles for each coin but that method was time consuming and too much repetition. From now on I will be adding mining procedure for new coin  in this post unless required and then I will create a dedicated post.

mining guides

 How to Mine Jolt Gas? : JLG 

Coin Ticker : JLG

JLG Mining Algo : C11

Jolt Gas  Exchange : No exchange yet

Jolt Gas Mining Pool : jkcpool.com

JLG Mining Performance : ~30 MH/s for 1080 ti

JLG Masternode : 2000 JLG, 50% rewards [ Interested in shared MN then mail me at [email protected]]

1. Download JLG Miner ( This is Alexis78 miner)

2. Download JLG Windows Wallet get your JLG receiving address.

4. Open batch file and edit as follows.

ccminer -a c11 -o stratum+tcp://jkcpool.com:3573 -u JfFTR4W3 -i 22

Replace “JfFTR4W3kAZ” with your JLG receiving address.

5. Run batch file, Happy Mining.

Lower the intensity if getting invalid memory error.

Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : 0

 How to Mine  Endrophin Coin? : END 

Coin Ticker : END

END Mining Algo : neoscrypt

Endrophin Crypto Exchange : No exchange

Endrophin Mining Pool : jkcpool.com

END Mining Performance : 1900 kH/s for 1080 ti

END Mining Profitability : ??? , 14-Feb-2018

Endrphin Price Now : ???

Coin is released few hours back and added it to the JkcPool.com

For 1080 ti  best miner is excavator miner, link to which is shared below, HSR miner provide 1800 kh/s and excavator miner provide 1900 kh/s

If you have 1070 or 1060 etc then use KlausT miner, and share results below which one gave you better performance excavator miner of KlausT ccminer.

1. Download  excavator Miner    KlausT ccminer

2. Download Endrophin Wallet

3. Get your receiving address.

3. Extract mining software and open “default_command_file.json” with notepad.

In above file change “EWdhuZa” with your receiving address.

Above file is for 7 GPU if you have 4 GPU’s then remove following from the file [ If you have less or more gpus then do accordingly]

{“id”:1,”method”:”worker.add”,”params”:[“0″,”4”]},
{“id”:1,”method”:”worker.add”,”params”:[“0″,”5”]},
{“id”:1,”method”:”worker.add”,”params”:[“0″,”6”]}

4. Run “excavator+web+restart_script.bat” file

Endrophin Mining Overclock Settings

Tdp : 80-100%

Core : = +50

Memory : 0

 How to Mine  RACECrypto? : RACE 

Coin Ticker : RACE

RACE Mining Algo : Lyra2v2

RACE Crypto Exchange : No exchange

Racecrypto Mining Pool : race.suprnova.cc

RACE Mining Performance : 70 MH/s for 1080 ti

Racecrypto Mining Profitability : ??? , 1-Feb-2018

RACE Price Now : ???

This coin in not available of any crypto exchanges. Mining difficulty is low, so I will mine some time.

1. Download RACE Miner

2. Create new account at https://race.suprnova.cc (Old account will not work)

3. Create worker (My Account >>My Woker)

4. Open RACE.bat file and edit as follows

ccminer -a lyra2v2 -o stratum+tcp://race.suprnova.cc:5650 -u username.Workername -p chcpass

Replace “username” with your suprnova username

Replace “Wokername” with name of worker you created on step 3

5. Run RACE.bat file, Happy Mining.

RACE Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : -300

 How to Mine Argo ? : ARGO 

Coin Ticker : ARGO

ARGO Mining Algo : skein

ARGO Coin Exchange : Crypto.Bridge

Mining Pool : protopool.net

Argo Mining Performance : 1000 MH/s for 1080 ti

Argo Mining Profitability : $6+/day/1080 ti, 3-Feb-2018

1. Download Argo Miner ( This is Alexis78 miner complied with CUDA 9)

2. We will be using protopool .

3. Download Argo Windows Wallet get your ARGO  receiving address.

4. Open bat file and edit as follows.

ccminer -a skein -o stratum+tcp://eu1.protopool.net:4933 -u AbX -i 28

Replace “AbX” with your Argo receiving address.

5. Run batch file, Happy Mining.

Lower the intensity if miner is not stable for you (-i 28).

Argo Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : -300

 How to Mine Garlicoin? : GRLC 

Coin Ticker : GRLC

GRLC Mining Algo : Scrypt-adaptive-N

Garlicoin Exchange : tradesatoshi.com

Garlicoin Mining Pool : garlicsoup.xyz

GRLC Performance : 400-500 Kh/s for 1080 ti

GRLC Mining Profitability : $10+ , 28-Jan-2018

Garlicoin Price Now : 0.000145 btc , $1.6

You need powerful cpu to mine this coin. If your miner is crashing then either miner ARGO or mine both GRLC & ARGO. In batch file use argument at the end, -d 0,1,2 in GRLC batch file and -d 3,4 in ARGO batch file if you have 5 gpus. 

1. Download Palginpav Ccminer ( 2.2.4)

2. You can download desktop wallet from github or use GRLC Web Wallet and get your receiving address.

4. Edit as follows.

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100

ccminer -L 2 -l T30x20 -R 15 -a scrypt:10 --lookup-gap=2 -o stratum+tcp://pool.grlc-bakery.fun:3333 -u GZ -p x -i 25 --cpu-priority 3
pause

Replace “GZ” with your GRLC receiving address.

5. Run batch file, Happy Mining.

Garlic Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : 0

 How to Mine Criptoreal? : CRS 

Coin Ticker : CRS

CRS Mining Algo : Lyra2v2

Criptoreal Coin Exchange : No exchange

Criptoreal Mining Pool : arcpool

CRS Mining Performance : 70 MH/s for 1080 ti

CRS Mining Profitability : ??? , 26-Jan-2018

Criptoreal Price Now : ???

This coin in not available of any crypto exchanges. Mining difficulty is low, so I will mine some for 2-3 days  and hold till it hit the exchanges.

1. Download CRS Miner

2. Download CRS Windows Wallet get your CRS receiving address.

4. Open CRS.bat file and edit as follows.

ccminer -a lyra2v2 -o stratum+tcp://arcpool.com:4533 -u CW

Replace “CW” with your CRS receiving address.

5. Run BHD.bat file, Happy Mining.

CRS Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : -300

 How to Mine Bithold Coin? : BHD 

Coin Ticker : BHD

BHD Mining Algo : C11

Bithold Coin Exchange : Stocks.exchange

Bithold Mining Pool : protopool.net

BHD Mining Performance : 30 MH/s for 1080 ti

Bithold Mining Profitability : $8+/2.5 BHD/day/1080 ti , 25-Jan-2018

Bithold Price Now : .00031 btc, $3.5

BHD POS : Hold coins in uncrypted wallet to get free BHD

1. Download BHDMiner ( This is Alexis78 miner)

2. We will be using protopool.net

3. Download BHD Windows Wallet get your BHD receiving address.

4. Open BHD.bat file and edit as follows.

ccminer -a c11 -o stratum+tcp://eu1.protopool.net:3573 -u hH -i 22

Replace “hH” with your BHD receiving address.

5. Run BHD.bat file, Happy Mining.

Lower the intensity if getting invalid memory error.

BHD Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : 0

 How to Mine Lizus Coin? : LIZ 

Coin Ticker : LIZ

LIZ Mining Algo : skein

Lizus Coin Exchange : Crypto-Bridge

LIZ Mining Pool : bsod.pw

LIZ Mining Performance : 1000 MH/s for 1080 ti

Lizus Mining Profitability : will share after few hours of mining, last updated on 18-Jan-2018

Lizus Price Now : .00075 btc, $8

1. Download LIZ Miner ( This is Alexis78 miner complied with CUDA 9)

2. We will be using bsod.pw pool.

3. Download LIZ Windows Wallet get your LIZ receiving address.

4. Open LIZ.bat file and edit as follows.

ccminer -a skein -o stratum+tcp://pool.bsod.pw:2016 -u 9T -i 28

Replace “9T” with your LIZ receiving address.

5. Run LIZ.bat file, Happy Mining.

Lower the intensity if miner is not stable for you (-i 28).

How to Sync LIZ Wallet ?

1. Open run box, Widows Key + R

2. Enter ” %APPDATA% ” and hit enter

3. Open Lizus folder add this file to the folder.

4. Restart Lizus wallet.

LIZ Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : -300

 How to Mine MUNCoin? : MUN

Coin Ticker : MUN

MUN Mining Algo : skunk

MUNCoin Exchange : stocks.exchange

MUN Mining Pool : suprnova

MUNCoin Mining Performance : 57 MH/s for 1080 ti

MUN mining Profitability : $12/Day/1080 ti, last updated on 13-Jan-2018

MUN Price Now : .0034 btc, $48

1. Download MUN Miner ( Trpruvot 2.2.4 )

2. We will use Suprnova pool, no need to download wallet.

Re-register on Suprnova and create woker again. Suprnova database reset. 

3. Extract the miner and add following to the batch file.

ccminer -a skunk -o stratum+tcp://mun.suprnova.cc:8963 -u anujsainicse.chcwork -p chcpass

Change “anujsainicse” with your  suprnova username.

Change “chcwork” with your workername

5. Run batch file and mining will start.

MUN Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : -300

 How to Mine Numus Coin? : NMS

Coin Ticker : NMS

Numus Mining Algo : skein

Numus Exchange : Cryptopia

NMS Mining Pool : protopool.net

NMS Mining Performance : 1000 MH/s for 1080 ti

Numus mining Profitability : $13/Day/1080 ti, last updated on 11-Jan-2018

1. Download NMS Miner ( Complied with CUDA 9 , if getting invalid argument error in original Alexis78 miner then either use CUDA 7.5 or this miner )

2. We will be using protopool.net as it have majority of hashrate.

3. Download NMS Wallet get your NMS receiving address.

4. Open NMS.bat file and edit as follows.

ccminer -a skein -o stratum+tcp://eu1.protopool.net:4933 -u 9T -i 28

Replace “9T” with your NMS receiving address.

5. Run NMS.bat file, Happy Mining.

Lower the intensity if miner is not stable for you.

NMS Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : -300

 How to Mine LuxCoin ? : LUX

Coin Ticker : LUX

LUX Mining Algo : PHI1612

LuxCoin Exchange : Cryptopia

Mining Performance : 35 MH/s for 1080 ti

LUX mining Profitability : $12/Day/1080 ti, last updated on 11-Jan-2018

LUX mining Pool : altminer.net , bsod.pw

1.  Download LUX Coin – PHI Miner,  LUX SP-mod(Check Pinned comment, can’t confirm the source if you are not comfortable then use regular miner or buy directly from SP for 0.05 BTC. This miner will give you 10% more hashrate)

2. Download LUX Wallet  and  get LUX receiving address.

3. Extract miner and open batch file and edit as follow

setx GPU_MAX_ALLOC_PERCENT 100
ccminer.exe -a phi -o stratum+tcp://eu1.altminer.net:11000 -u LN -i 21

Change “LN” with your LUX wallet address.

4. Save and run the batch file.

If you have LUX spmod then you will get 10% more hashrate.

LUX  Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : 0

 How to Mine Zero Coin? : ZER

Coin Ticker : ZER

Zero Coin Mining Algo :  EquihashZero

ZeroCoin Exchange : Cryptopia

Mining Performance : 15 sol/s for 1080 ti

ZER mining Profitability : $11/Day/1080 ti, last updated on 12-Jan-2018

Zero Coin mining Pool : suprnova

Zerocoin mining is unstable if you have multiple gpu’s. Miner works great if you have 1-3 gpus or if you have more gpus then powerful cpu like i5,i7 and 16 GB RAM needed.

Miner need large page file size.e.g if having 3 X 1080 ti then page file size should be 33 gigabytes.

1.  Download Zero Coin Miner – Optiminer Zero

2. Visit Suprnova and create new worker.

3. Extract miner and open batch file and edit as follow

optiminer -s zero.suprnova.cc:6568 -u anujsainicse.chcwork -p chcpass -m 8080
 pause

Change “anujsainicse” with your  suprnova username.

Change “chcwork” with your workername

4. Save and run the batch file.

Zero Coin  Mining Overclock Settings

Tdp : 100

Core : = +50

Memory : 0

Reader Interactions

Comments

  2. Muth SXb says

    i have a “gigabyte gtx 1080 ti gaming oc black”, i put the OC settings into afterburner. I get only something lie 880MH/s… I don’t understand why? (my card is brand new, i get it last week)

    Reply

  3. Jaz360 says

    Hi, thanks for the guide I am new to mining I followed all of your steps and started mining nms but how do I check if I made anything?

    Reply

  4. Coin Dings says

    @disqus_8s7EThyS6P:disqus thank you for your work and for helping everyone! You are great! Do you have a wallet address we can donate to?

    Reply

  8. Michael Doan says

    This kind of discussion may be worth an entire dedicated article, but how do you know when difficulty changes for a coin? I found this info on the NMS page:

    POW Reward Scheme:
    81 – 400 Block – 1 NMS per Block
    401 – 10 000 Block – 10 NMS per Block
    10 001 – 30 000 Block – 8 NMS per Block
    30 001 – 50 000 Block – 6 NMS per Block
    50 001 – 70 000 Block – 4 NMS per Block
    70 001 – 100 000 Block – 2 NMS per Block

    POS Reward Scheme:
    401 – 10 000 Block – 10 NMS per Block
    10 001 – 30 000 Block – 12 NMS per Block
    30 001 – 50 000 Block – 13 NMS per Block
    50 001 – 70 000 Block – 14 NMS per Block
    70 001 – 100 000 Block – 15 NMS per Block
    100 001 – 200 000 Block – 10 NMS per Block
    After 200 001 – 8 NMS per Block

    How do you read this to know when mining is more/less worth it for this coin. I think we are on block 67000 right now.

    Reply

    • ANUJ SAINI says

      I will be mining it 70K block, price and difficulty also increasing.
      Difficulty increase-decrease frequently, since protopool have majority of hashrate so I keep track of number for miners mining it. Yesterday around 800 miners mining NMS and now around 1100.
      At the bottom of page there is block mBTC/Mh/d – check last 24 hours and last hour profit to know is it worth mining anymore.

      Currently working on crypto mining forum site, will be launched very soon

      Reply

  11. Eclipsie says

    Anyone having problem with LUX coin on Altminer site? Hash rate jumps way down and then shoots back to normal. Currently at 190mhs, but jumps down to 75mhs sometimes. I understand the fluctuation due to hash rate verification during the time interval. But, it should not jump lower than half your hash rate. Anyone else having this problem?

    Reply

  12. CJ Oosthuizen says

    How long does it take for the NMS to pay to your wallet. I know I must wait, but just roughly how long did you wait for the NMS to show up in your wallet?

    Reply

  13. Coin Dings says

    @disqus_8s7EThyS6P:disqus Iยดve sent my NMS to cryptopia deposit but they are stuck since 18 hours on confirmation 17/20, do you know what I could do to get them confirmed? Thanks

    Reply

        • Coin Dings says

          Usually it takes 15 min for me too, but this one time yesterday it got stuck on cryptopia and still isnยดt confirmed. I donยดt know what to do

          Reply

          • Vu Khuong Duy says

            @disqus_8s7EThyS6P:disqus : it happens when i mine Signatum before. After block 70k, people may stop mining because not profitable anymore and price drop. I see no future of this coin ^^ So i will sell most of my coins before 70k ^^

          • ANUJ SAINI says

            I have also mined SIGT for at least one month and SIGT was the coin I holded, thought price will increase after POS but dev left the project and SIGT loose its value by 90%.
            SIGT team launched new coin straks and there was swap 1 straks for 4 SIGT. I told everyone on Telegram to buy SIGT for *60 BTC and during swap SIGT price reached to *350 and I sold mine at *250. Best 4X trade ever within few days.
            Another cool thing is during initial days of mining Straks, I was getting around 200 straks/day/7 1080 ti but was around $0.4 at that time. I decided to hold straks and sold all when Straks when straks price was $3, was very happy because I sold for 6X which will give me profit of $100/day/1080 ti. But during pump Straks price reached $28, if holded for more time than it could be $1000/day/1080 ti , 1080 ti ROI would be 1 day.

            No regrets, lost so much money by mining and holding SIGT but made so much SIGT and Straks pump.

            Hoping price drop happened with NMS.

          • Vu Khuong Duy says

            i got 53 STRAKS for 1st week of swap. and sold them all for 12-13$. I think the price will drop gradually to <1$. Congrats man !!! . Mining when people ignore it, sometimes, earn crazy money ^^ Everyone is so upset with SIGT.

  16. Tom says

    When I start the .bat file for MUN it flashes real quick and disappears. I’ve input all the correct information. Any idea what is happening?

    Reply

  17. Oliver Diekmeier says

    Hi Anuj, do you know smth about this issue on Cryptopia: “Failed to generate new address” when tryping to deposit ZERO?
    Also, could you maybe add an info how the new coins you present almost daily compare to ZER? Only if itยดs not a lot of trouble ofc ๐Ÿ™‚ It would also be nice to know if the other coins are also power efficient (zero uses 70% tdp on my rig) or use 100% like NMS. I prefered ZERO since itยดs power efficient, but I dunno if the difficulty / block reward still make it profitable. Would be appriecieated if you could give us (Zero miners) some info about itยดs current state.
    @edit: Btw, why do you always underclock your memory? Doenst it decrease the Hashrate? I am running +1200 on Mem and it gives around 0,3sols more

    Reply

      • Oliver Diekmeier says

        Yh, sadly Cryptopia is the only one for Zero. Kinda sad it fcked up now, since Zero is rising nicely. Could possibly hit 10Euro today, would suck to miss it ๐Ÿ™

        Reply

        • Michael Doan says

          I hear you. I have ZER as well I’d like to unload. NMS went from $27 – $43 in 24h and I can’t sell it cause Cryptopia is backlogged with support tickets.. brutal

          Reply

    • ANUJ SAINI says

      Maximum nvidia cards algo don’t need much memory so no effect in hashrate if mem increased.
      I lower memory to save electricity, no impact on hashrate but lesser power is needed by card to run.

      Yes cryptopia having issue with deposits, me also can’t generate NMS deposit address. Zero coin right now will give you $10+/day/1080 ti

      Reply

      • Oliver Diekmeier says

        Mined ZER on http://zero.forgetop.com for a few hours. Their chard estimated my gains at 6$ a day on 1080ti. Pretty lowish, thus I will give MUN a try now. Do you think the 6$ are a misscalculation or why is it so low? The price is at around 8Euro so not bad.
        Did the Difficulty raise so much or for what reason would the gains drop by 50% ?

        Reply

        • ANUJ SAINI says

          Mine on suprnova, you earn less because of pool you choose.
          Suprnova have majority of hashrate so your earning will be stable there. In small pools earning can be more and less based on how many blocks pool find out

          Reply

          • Oliver Diekmeier says

            Thanks, back to nova then. It kinda sucked their ZER was bugged, no charts and other info. Seems to work again now, maybe they missed me ๐Ÿ™‚

  18. feelinfroggy says

    So I am totally new to this. I have 2 1080ti’s that I was using for gaming, but I decided to start mining with them a couple of days ago. I am using Nicehash, since I am a beginner should I continue to use Nicehash or am I missing out on a lot of cash.

    Reply

    • ANUJ SAINI says

      Don’t use nicehash if you want to earn more. Nicehash have advatange that you don’t have to worry about new profitable coin to min, when/where to sell, exchange etc, you get paid in btc but you will earn 30%-40% less

      Reply

  19. Hristo Angelov says

    Hi! I’m happy I found this blog!
    I just registered on stocks.exchange, since this is the one I found which can exchange mun to btc (actually I would prefer eth, but there wasn’t such an option..), so is this exchange site ok? Could you prefer a better exchange site? Thank you!

    Reply

  20. Eclipsie says

    How long do you think LUX coin will still be good to mine in your opinion? What block number do you suggest we stop mining it at do you think?

    Reply

  22. Eclipsie says

    IS there a huge delay in Deposits to Cryptopia? My last coins pop up farley quickly in deposit History. Its been over an hour now, and i don’t even see my coin in deposit history. Check my address i sent too and confirmed the address. Has anyone else experienced this problem with Cryptopia ?
    Coin finally popped up ๐Ÿ™‚

    Reply

    • Hans says

      It also seems to differ from one coin to the other. Luxcoin usually shows up within 15 minutes (at least as unconfirmed), but BTX usually takes much longer. Sometimes a couple of hours before you can actually exchange it.

      I do however find this exchange much better than stocks.exchange (very high withdrawal fee) and Crypto Bridge (not so many coins, rather small user-base, which makes getting getting a good price for your coins a bit hit and mis).

      Reply

        • Hans says

          I’ve got 3 rigs with 8 cards, one of which is still aimed at LUX. It still provides me with $8,70 per card of actual payout.

          I find that profitability fluctuates throughout the day and sometimes a coin that Anuj proposes works for a couple of hours, but then all of a sudden doesn’t deliver anything anymore. So when switching to one of his newer suggestions, I usually try it on one rig for a couple of hours before pointing more cards towards this coin. As long as they remain within a 10-20% margin, I’m mining 2 or 3 coins simultaneously, allowing me to signal yield dropoff within 4 – 6 hours, while still getting a good profit. That way your maximum profit isn’t achieved, but since I also have a daytime job and a family, so it provides me piece of mind, knowing the average is still very good.

          Reply

          • ANUJ SAINI says

            I might create auto algo switching powershell script which will automatically switch to best minable coin based on price and difficulty.
            But right now very busy in other projects

          • Eclipsie says

            Thankyou for your info. ๐Ÿ™‚
            What TDP do you mine at?
            Thinking of buying another rig. Do you mind if you can post your setup please?
            Trying to get another idea of a setup, so far mine is close to ANUJ setup but 1 PSU and 6 cards.

      • Landak Cemong says

        Thx. Can you explain a bit more? Do you need to convert it into a more popular coin first like BTC, ETH, etc or directly to USD?

        Reply

        • ANUJ SAINI says

          Watch some crytpo trading videos on Youtube. Don’t use BTC for transfer. Use Litecoin,Doge to transfer between exchanges.
          Do like this sell these coins for BTC then BTC for LTC/DOGE/etc ( low transfer fees coins with good volume) then transfer LTC/DOGE to other exchanges then LTC/DOGE to BTC then Fait

          Reply

  24. Eric Smith says

    Liz make my computer crash, anything particular to do ?
    Instead, I am mining 3 x BTX, is there anything better to do, I now use 3 cards

    Reply

  27. Oliver Diekmeier says

    After some minutes of LIZ mining I get a “Stratum connection interupted” in the console and the miner turns off. Do you perhaps know the issue?

    Reply

  28. Michael Doan says

    Newb question. What does the LIZ “wallet sync” do. I haven’t had to do that for other coins/wallets.
    Thanks!

    Reply

    • ANUJ SAINI says

      Some miners were facing problem that their LIZ wallet is not syncing with blockchain.
      Maximum time all coins wallet sync automatically but for some coins we have to specify nodes manually

      Reply

  29. Eclipsie says

    Update Jan. 18, 2018 Mining LUX on Yiimp.eu with 6x1080Ti I received 1.90283117LUX over 24 hour period. that is 0.317Lux per day, per 1080Ti. Selling @ 0.0025Btc, and Bitcoin @ $11,350, a profit of “$8.99 per 1080Ti, per day” Power to Gpus @ 65 TDP. Anyone else mining LUX please let me know what you received, or any questions i can help with. Cheers ๐Ÿ™‚

    Reply

    • Ondล™ej Zelรญk says

      I am still on altminer and I am really not very satisfied with revenue I get. Getting now around 34 MH/s but looks like I have made only 0,05 LUX per 8 hour. I would like to try Yiimp but I am still very new to this, can you please share your batch file? Also what do you guys think of changer.com as a DOGE->LTC exchange site? Looks legit and hopefully with not big fees. I wanted to try Bittrex but it is unaivaible to log for new users.
      Also Eclipsie my LUX Wallet started to not responding today too, so you are not alone.

      Reply

    • ANUJ SAINI says

      Sorry I was out today. LIZ was very good yesterday gave $15/1080ti . Just checked now LIZ price is down 30% and difficulty also increased, today it is $8+/1080 ti

      Reply

  32. Zeeshan Mansoor says

    anyone having their LUX wallet get stuck or not respond? It keeps freezing and i have to wait for it to respond especially when sending

    Reply

  36. mike goldsmith says

    LUX the new dump coin of the day, seems like your actually trying to hurt the community by “helping” the idiots who can’t think for themselves.

    Reply

  37. haha says

    @@disqus_8s7EThyS6P:disqus is it normal if your gpu usage is dropping like this?(lux-sp-mod)

    6https://uploads.disquscdn.com/images/f82d11c7ab9a74ed26d459293d145f41ecd9408ae1eb43fc04cf35950918ab03.png

    Reply

    • ANUJ SAINI says

      No my graph is not like this its between 80%-100%. How was the graph when using regular miner for LUX. There can be problem with LUX sp mod as I can’t verify the source but for me sp mod working fine
      LIZ also good to mine right now, you can mine that also

      Reply

      • de ondergang says

        Mining regular LUX or LIZ is no problem, it’s steady 100%.
        Any idea’s or changes i need to make to the batch file that was pinned?
        sp-mod lux is only 2-3mh/s faster it seems.

        cheers

        Reply

        • ANUJ SAINI says

          Yes, only 2-3 mh faster, initially gave around 6-7 mh but after few minutes it is 2-3 mh faster.
          No additional changes required in batch file, change pool which is shared in the post and your wallet address

          Reply

  38. Cรฉdric Servais says

    The Liz miner is great +20Mh per second. Cant find any Cuda 9 doing the same hash rate but windows keeps saying it’s a virus and delete it. I have already disabled it three times but yesterday it re-enabled and deleted the file/process while I was sleeping. Kind of mad..

    Reply

    • ANUJ SAINI says

      I keep all my wallet on my personal computer with some anti virus enabled.
      On mining machine I just disable antivirus. If you are unsure about miner source as we have lux mod then don’t run miner as administrator, you are good to go

      Reply

  39. Ricardo Machado says

    what better overclocking by NEOSCRYPT with Gigabyte Aorus GTX 1080 TI turbo 11gb ddr5x? Here 1.400h/s per card with +120 / +400 / 220W mรกx. (simplemining).

    Reply

  42. bokos says

    Hello!
    I use this at batch file with SP mod miner:
    @echo off
    ccminer -a phi -o stratum+tcp://eu1.altminer.net:6667 -u LiARsJ1h37uttgy7XzQc57P89FTkhSffAB -p c=LUX
    pause

    TDP 80% | +75 core | -200 mem | 250w Total PC Consumption

    I get 33.3 MH/s with a Zotac 1080 Ti Mini
    Is that normal?
    Do I have to add anything to the batch file ?

    thanks

    Reply

  43. Bรฉci says

    TDP 80% | +150 core | -200 mem | Custom fan with max 55-57 degree
    37,5 MH/s – Assus Strix 1080 TI oc – 9,8-10$/day
    Got my third strix today ๐Ÿ™‚

    Reply

    • Maca Bond says

      Not at the moment but Massdrop sometimes make it available for $660 $680 few months back. Rightnow its shortage everywhere even OEMs so wait for the drop to available again.

      Reply

  45. Justin Murray says

    I’m only getting 25.5 MH/s hash rate on my gtx 1080, buddy is getting over 200 on his GTX 970, where can I look to fix the issue?

    Reply

      • Justin Murray says

        I am running +50 core and +0 memory, using the ccminer listed here with the SPmod for LUX.

        Clock speed is running consistently between 1900 and 1950. I can try comparing with my friend to see if I installed correctly

        Reply

          • Justin Murray says

            thanks, I’ll research more. If we were closer in hash rate I wouldn’t think much of it but my card outperforms his by 25% and I’m getting 1/10th of his hash rate

          • Justin Murray says

            confirmed, he was mining a different coin and it was a miscommunication. My hashrate of 26 MH/s appears to be pretty normal for LUX

    • ANUJ SAINI says

      Yes power consumption graph is similar to mine.
      Mine for few more hours to get exact results, you should expect mining .25 LUX/day/1080 ti.
      BHD is also good one to mine right now. Posting guide within few minutes

      Reply

  52. Jason Robbins says

    Have been following these updates, thanks. Currently mining Lux. Tried setting up Argo though and can not get the miner to run, even when lowering the intensity. Any suggestions?

    Reply

  56. disqus_uRlaHDE5rA says

    i mined on grlc-bakery.fun
    see Total Received (GRLC) – 27.52220910
    when i can receive 27 coins to my wallet in tradesatoshi.com?

    Reply

    • TheYagerD says

      Which wallet are you using? I have made multiple GRLC transfers to tradesatoshi and each one takes roughly 15 mins.

      Reply

  57. kettler says

    Hey guys,

    I’m going at it with a 1080TI on LUX getting about 36 MH/s . Anyone getting more ? If yes what setting u using? ( Using the settings in SP mod btw )

    Thanks!

    Reply

  58. Bรฉci says

    So, Mining for few days LUX with 2*Asus rog strix 1080ti.
    whattomine says for 72 Mh/s: 0.662601 LUX for reward in one Day
    geting about 72-74 Mh/s all day for 2 cards.

    Calculated for last 2 days:
    2 days ago at 19:00: 1.04119404 LUX
    1 days ago at 19:00: 1.52909404 LUX
    today at 19:00: 2.00285780 LUX

    Calculated it is a reward of 0,47-0,48 LUX for one day…. do I miss something? Or is whattomine not as precise as I thought?

    Reply

  59. MrVi Di says

    Hiii! Have a question for post owner. What you think about zcl and btc private fork?
    In your opinion what better to do: sell before fork or hold and expect to btcp good run? Maybie this topic will be good to your new blog post? It would be great to listen what people thinks

    Reply

  60. Coin Dings says

    How did you guys get your garlic wallet adresses? I made an account on garlicwallet.com, but theres just no wallet adress anywhere…

    Reply

  62. Jmart83 says

    Does anybody else get worse results with the new miner posted for garlic? Instead of 10 to 20% higher I get 10 to 20% lower hash. The new miner doesn’t seem to make any difference for the high CPU load.

    Also has anybody found a workaround for the cpu bottleneck? Somebody on Reddit claimed in a PM that his buddy found a fix but didn’t wasn’t willing to share it. The only other writhing fix I’ve seen is to buy an i7. Right now I can only mine garlic on one 1080ti with CPU slightly under 100%. If I try two it will work but the hashrate per card is lower and the hashrate on my third card mining ARGO is reduced significantly.

    Reply

      • Jmart83 says

        Yes. I only spent 10 minutes trying it before leaving for work this morning, but with a single 1080ti I went from ~550 kH to ~480kH with the miner Collin posted along with the bat file posted in this guide.

        Reply

        • TheYagerD says

          It raised my hashrate a lot. Maybe try to change cpu priority, intensity or change virtual memory? What cpu do you have?

          Reply

    • ANUJ SAINI says

      Some algo need more memory and some does not.
      For Algos which don’t need much memory, I underclock the memory to save little bit of electricity without impacting hash rate

      Reply

  65. Ximo Roca says

    why are you recomending 100% tdp on all coins?

    lowering the tdp a bit gives better efficency, while staying very close in hashrate.

    ie: with grlc im getting the same hashrate (450kh) with ur settings tan just going 75% tdp and +75 core, while with this im using 40w less, my temps are like 6c lower and my fans run like 15% lower (better care of the gpu)

    Reply

    • ANUJ SAINI says

      Electricity cost is very low here. Around $0.05 per killo watt. So for me 100% tdp is best, otherwise tdp at 80% is most efficient considering electricity cost and gpu temperature.
      For effective cooling I place my rig in closed room with exhaust fan

      Reply

  66. omuyeti says

    Hi guys,

    Started to mine Lux, installed the wallet, seems to be going with 74mhs on 2x1080ti .
    Question : are there any stats regarding earning ? or i just have to wait to see something in the wallet ? and if anybody knows how long will it take to get the lux coins in the wallet..transfers like one every 24h or ? thx all

    Reply

    • kettler says

      it’s based on the pool, have a look at the site where you’re mining at they should have info on when and at what minimum sum they deposit at. I’m using altminer they depoit at 0.05

      Reply

      • omuyeti says

        Thx for the info my friend. I got all the infos from the site.
        Question , maybe somebody knows : i use Lux SP mod miner, seems to work fine but from time to time it gets stuck, doesn.t say anything but it stops producing. If i manually press S, seems to start again.
        Any idea how to automatically start it or why is does this ?

        The bat file looks like this , if it matter
        :loop
        setx GPU_MAX_ALLOC_PERCENT 100
        ccminer.exe -a phi -o stratum+tcp://eu1.altminer.net:11000 -u luxcon_address -i 21 -R 5
        goto :loop

        Not sure what -i 21 and -R 5 actually means.

        Reply

        • kettler says

          @echo off
          TITLE PHI (LUX) – futurecoins pool
          setx GPU_MAX_ALLOC_PERCENT 100
          ccminer.exe -a phi -o stratum+tcp://eu1.altminer.net:11000 -u xxxx -i 22 -p c=LUX
          pause

          This is what I use and it never gets stuck.the 10% on the miner doesn’t seem to work if you up the core clock to much.

          Reply

  67. Kamal Ahmad says

    I am using this code for Garli Mining but nothing happens except the repeating code in the command window, what is the reason ? do I have to do some thing else with this code

    setx GPU_FORCE_64BIT_PTR 0
    setx GPU_MAX_HEAP_SIZE 100
    setx GPU_USE_SYNC_OBJECTS 1
    setx GPU_MAX_ALLOC_PERCENT 100
    setx GPU_SINGLE_ALLOC_PERCENT 100

    ccminer -L 2 -l T30x20 -R 15 -a scrypt:10 –lookup-gap=2 -o stratum+tcp://pool.grlc-bakery.fun:3333 -u GZXDVUpw7Wht6vYUjZFz5AaBz4i67KuuGA -p x -i 25 –cpu-priority 3
    pause

    Reply

  68. Raul says

    hy, in GARLIC i just get 250 to 297 KH/S, with 100% power and 50 memory. I am doing something wrong or something happend with GARLIC this last day? 1080 ti and cpu is PentiumG4400

    Reply

  70. Danil Shvedov says

    Note on GRLC mining: option -l T56x20 gives much more (600+ kH/s) on my card VS 450 kH/s with -l T30x20
    If T56x20 does not work – try T55x20.

    Reply

  71. ๅพ่ดต says

    There is a big problem about LUX wallet,that the wallet balance is out of sync.Mining LUX coin for one day and the pool paid to my address but no coin in my LUX wallet.I have no idea what happened and how to solve it.

    Reply

        • ANUJ SAINI says

          Add nodes below to lux.conf in %appdata%/Lux folder and wait for syncing, can take for a while.

          addnode=176.32.5.50:26868
          addnode=198.91.220.149:26868
          addnode=212.253.248.210:26868
          addnode=217.101.193.61:26868
          addnode=219.75.75.71:26868
          addnode=24.8.183.131:26868
          addnode=45.76.118.90:26868
          addnode=66.160.165.8:26868
          addnode=73.160.169.87:26868
          addnode=74.58.249.254:26868
          addnode=78.124.167.38:26868
          addnode=78.243.65.55:26868
          addnode=81.108.220.210:26868
          addnode=85.253.146.172:26868
          addnode=94.29.245.244:26868

          Reply

          • akmotte says

            I did first modify the json file accordingly to my rig but it’s not working. I already removed the last comma of course but that didn’t work either, the problem is something else.

            [
            {“time”:0,”commands”:[
            {“id”:1,”method”:”algorithm.add”,”params”:[“neoscrypt”,”jkcpool.com:4233″,”myaddress:c=END”]}
            ]},
            {“time”:3,”commands”:[
            {“id”:1,”method”:”worker.add”,”params”:[“0″,”0”]}
            ]},
            {“time”:10,”loop”:10,”commands”:[
            {“id”:1,”method”:”worker.print.speed”,”params”:[“0”]},
            {“id”:1,”method”:”worker.print.speed”,”params”:[“1”]},
            {“id”:1,”method”:”algorithm.print.speeds”,”params”:[“0”]}
            ]}
            ]

    • Philip Anthony Domingo Ignacio says

      Download the excavator at nicehash then edit the default command file in there. It works just fine for me now.

      Reply

  76. ๅ…Žไบœ says

    I’m mining Endorphin with Klaus-T miner. But, I couldn’t receive any END after 3 hours of mining. Do you know the way to solve this problem?

    Reply

  77. Coin Dings says

    I have been mining for 1,5h but the pool shows 0 earned END coins, eventhough it shows:
    Summary Miners Shares Hashrate* Reject*
    neoscrypt 1 1.7442% 4.6 Mh/s

    Reply

    • ANUJ SAINI says

      Many users don’t join the pool as of yet and last END block find by the pool is 42 hours ago.
      If was unlucky pool can’t find the block, main reason is we don’t have enough hash power there.
      Just checked your address you have 10% share, so once pool find next block you will get your reward accordingly

      Reply

Leave a Reply

Your email address will not be published. Required fields are marked *